Quick Answer: How Do I Troubleshoot My Bell Fibe TV?

How do I reboot my bell receiver?

Press and hold-down the green POWER button on the front of your TV receiver for 5 seconds (until the red, green, and blue lights come on).

Wait a few minutes for the reboot to take place..

Why is my bell receiver not working?

Try resetting your receiver by pressing and holding the POWER button on your receiver for at least 5 seconds until it resets. If you’re still having issues, please contact us. Try resetting your receiver by pressing and holding the POWER button on your receiver for at least 5 seconds until it resets.

How do I reboot my receiver?

To reset your receiver:Unplug the receiver’s power cord from the back of the receiver or from the wall outlet.Leave unplugged for 30 seconds and plug back in.The receiver should boot up properly in less than 90 seconds.

Why is my converter box not working?

Make sure your antenna is connected properly to the antenna input of your digital-to-analog converter box or digital television. … If you do not see a set-up menu or picture, tune your TV to channel 4. If you still do not see a set-up menu or picture, recheck your connections.

How do I connect my Bell Fibe remote to the receiver?

Nova RemoteTouch Menu to open the side navigation panel.Touch Settings.Touch the Pair your receiver button.Touch Next.On your Fibe TV remote, press the INTERACTIVE TV button.From the App launcher, select the Fibe Remote app.Scroll to and select Pair a device.Select Next.More items…

How do I reset my Bell Fibe modem?

How to reboot the modem for Fibe TV serviceOn your modem, locate the power cable.Remove the cable. … The lights on the front of your modem (except for the power LED) will blink as the modem goes through its start-up routine.Wait until the WAN, INTERNET and TV lights turn blue.More items…

How do I reset my Bell Fibe remote?

Reset my Fibe Slim remote to factory defaultTurn on your TV.Turn on your FibreOP TV receiver.Point your FibreOP TV remote at your TV.Press and hold the OPTIONS button for 3 seconds until the green TV light blinks twice.Enter the 0000 using your remote’s number buttons. You must enter the code within 10 seconds.The remote is set back to factory settings.

How do I reset my strong receiver?

If properly plugged in, try to reset your receiver by unplugging the power cord for about 30 seconds before plugging it back in. If that does not solve the problem, you may have to change the connection cables. Contact your local Strong dealer or point of sale.

Why does my Bell TV keep freezing?

General pixilation and freezing occurs when there is a disruption in the TV signal, or there is a weak signal altogether. Check your connections: Unplug the HDMI cable from your Bell MTS Fibe TV Set-top Box. … Make sure all cables connected on the set-top box and your TV are secure.

Why is my remote not working for my TV?

There are a number of reasons why your remote may not be working. The most common are physical damage, battery issues, pairing issues, or issues with the infrared sensor on the remote or TV. Replace the batteries and turn the TV off and on again at the switch. …

How do I connect a second TV to my bell receiver?

How to install additional wireless receiversConnect the receiver to the TV using an HDMI cable. … Turn your TV on and connect the receiver to a power outlet. … Go to the transmitter to confirm that it is turned on and that the Wi-Fi light on the transmitter is solid green or flashing green.Press the transmitter’s WPS button.More items…

How do I reset my Bell TV?

To reset your receiver to the factory default settings:Press MENU on your remote control.Select System Setup.Select Factory Defaults.A pop-up message will appear to confirm that you want to reset your receiver to the factory default settings.Select Yes.

Why isn’t my Bell Fibe remote working?

Before you begin troubleshooting, make sure that the batteries haven’t run out and that there are no obstructions between your remote and the TV. Make sure that the LED lights turn on when you press the buttons on the remote. Clear the remote programming commands and then reprogram the remote to work with the TV.

How do I program my Bell Fibe remote?

Nova RemoteTurn on your TV. On your Fibe TV remote, press and hold SETUP until LED light blinks twice.Press the TV button.Press and hold the SELECT button.Release the SELECT button when the TV turns off.Your Fibe TV remote should now be programmed to work with your TV.

Why is my Fibe TV not working?

Unplug the power cable on the back of the Fibe TV receiver. … Wait approximately five minutes for the Fibe TV receiver to restart. Once the Fibe TV receiver has restarted, check to see if your TV picture has returned and the Fibe TV receiver responds to the remote control.

How do I update my bell receiver?

Press Menu on your remote control (on 9400 models or older) or Menu followed by Settings (9500, 7500) and select Preferences. Select Updates….Press Menu on your remote control.Select Updates.Choose a time that is more convenient.Select Done.