- Can I use 18 gauge wire for LED lights?
- What size cable do I need for 100 amps?
- What size wire do I need for a 30 amp 220v circuit?
- Can 12 gauge wire handle 30 amps?
- What size wire is needed for a 200 amp service?
- How many amps is #6 wire good for?
- What size wire is good for 600 amps?
- What happens if wire gauge is too big?
- Can I use 8 gauge wire on a 20 amp circuit?
- What size wire do I need for a 1000 amp service?
- How do I calculate what size wire I need?
- What size wire do I need for 10 amps?
- What size wire is needed for a 20 amp 240 volt circuit?
- Which wire size will carry the most amps?
- How many amps can a 60 amp breaker handle?
- How many amps will 2 AWG carry?
- Can 10 gauge wire handle 50 amps?
- What size wire do I need for 60 amps?

## Can I use 18 gauge wire for LED lights?

Now, I personally use a solid core 18 gauge wire for all my lights and would recommend you do the same.

The cost difference between it and smaller cable is essentially negligible, and 18 gauge is about as big as you can go if you still want to be able to fit it into most COB holders or terminals..

## What size cable do I need for 100 amps?

When it comes to the lines connecting master and secondary panels, where the line will carry as much as a full 100 amps, use a 2-gauge non-metallic sheathed electrical cable. The cable must contain one or two hot wires depending on your needs, one neutral wire, and one ground wire. Each wire should be 2-gauge in size.

## What size wire do I need for a 30 amp 220v circuit?

Any circuit fused for 30 amps must use a minimum of 10 ga copper or 8 ga alu. Longer runs may require an upgrade of wire size. In your case, use at least 10 copper for your welder regardless how far it is from the breaker panel.

## Can 12 gauge wire handle 30 amps?

No. 12 gauge wire is rated for a maximum of 20 amps. You need a minimum of 10AWG wire for 30 amps.

## What size wire is needed for a 200 amp service?

SERVICE ENTRANCE CONDUCTORS SIZE AND RATINGService or Feeder RatingCopper ConductorsAluminum or Copper-Clad Aluminum125 Amps#2 AWG#1/0 AWG150 Amps#1 AWG#2/0 AWG200 Amps#2/0 AWG#4/0 AWG1 more row

## How many amps is #6 wire good for?

Size & AMP RatingsNM, TW, & UF WIRE (Copper Conductor)SE CABLE (Copper Conductor)12 AWG – 20 AMPS6 AWG – 65 AMPS10 AWG – 30 AMPS4 AWG – 85 AMPS8 AWG – 40 AMPS2 AWG – 115 AMPS6 AWG – 55 AMPS1 AWG – 130 AMPS1 more row

## What size wire is good for 600 amps?

Wire Size and Amp RatingsWire Size75°C (167°F)AWG(mm²)Copper500(253)380600(304)420700(355)46017 more rows

## What happens if wire gauge is too big?

using larger wire will not hurt anything or cause any overload. The larger wire will cost more, the pathway or where it has to fit, and the physical size of the connecting means (ie. the size of terminal or clamp it has to fit in), will all be determining factors in just how big is too big.

## Can I use 8 gauge wire on a 20 amp circuit?

You can usually fit 10 AWG wire under the screw; 8 AWG usually won’t fit. … Whereas 12 AWG is rated for 20 amps and 8 AWG is rated for 40 amps under normal conditions, a circuit wired with 12 AWG could drop below 110 volts at the end of a several hundred foot run when loaded to capacity.

## What size wire do I need for a 1000 amp service?

Wire Size Chart and Maximum Amp RatingsSIZE60°C (140°F)75°C (167°F)AWG or kcmilTYPES TW, UFTYPES RHW, THW, THWN9004355201000455545125049559026 more rows

## How do I calculate what size wire I need?

Divide the voltage running through the cable by your target current. If, for instance, 120 volts will act on the cable, and you want 30 amps to run through it: 120 / 30 = 4. This is your target resistance, measured in ohms. Multiply the cable’s length by its material’s resistivity.

## What size wire do I need for 10 amps?

For a maximum of 10 amps, you’ll need a wire gauge of 16.

## What size wire is needed for a 20 amp 240 volt circuit?

Use 12-gauge wire for a 20-amp circuit, 10-gauge for 30 amps, 8-gauge for 40 amps, and 6-gauge for 50 amps. Check local codes for requirements.

## Which wire size will carry the most amps?

Why Wire Gauge Is ImportantWire UseRated AmpacityWire GaugeElectric clothes dryers, 240-volt window air conditioners, electric water heaters30 amps10-gaugeCooktops and ranges40-50 amps6-gaugeElectric furnaces, large electric heaters60 amps4-gauge5 more rows

## How many amps can a 60 amp breaker handle?

Rough rule of thumb for residential thermal magnetic circuit breaker on instantaneous operation, 4-10 times the name plate rating 60 amp CB 240 amps-600 amp.

## How many amps will 2 AWG carry?

Ampacities of Wire Types (w/ Temp Rating) @ 0-2000 VoltsWire Size AWGTW, UF (140°)FEPW, RH, RHW, THHW, ZW, THWN, XHHW, THW, USE (167°)11101302951153851004708513 more rows

## Can 10 gauge wire handle 50 amps?

For no more than 3 current-carrying (copper) conductors in a conduit/raceway, you’d need a minimum of #8 AWG and depending on the ambient temperature around the conductor, #6 AWG. No. … 10 AWG coper wire is rated for 30 Amps in most installations. 50 Amps calls for 6 AWG or 8 AWG high temperature cable.

## What size wire do I need for 60 amps?

That would be 4-gauge wire. In practice, however, it’s common to wire 60-amp breakers with 6-gauge, 3-conductor wire because an appliance that needs a 60-amp breaker seldom draws the full 60 amps. If you’re installing a 60-amp subpanel, however, it’s best to connect it to the main panel with 4-gauge wire.